CO2 SYSTEM

 45 KG CO2 CYLINDER (MODEL D-611)

DEMCO 45Kg CO2 Fire Suppression agent is pressurized to 58.6 Bar at 21°C (850 psi at 70°F) and stored in 68L of seamless cylinder with each containing 45kg of liquefied CO2 agent. The element of CO2 is colourless, odourless, non-corrosive, non-conductive to electricity and work fast to vanish fire by decreasing the oxygen level that does not harm any property in the area.This system can be engineered to suit specific customer requirements. The indicators of audio and visual can be integrated into the control system that facilitates automatic trigger of fire doors, dampers and shutter.

DEMCO 45Kg CO2 Fire Suppression System is designed in accordance with National Fire Protection Association (NFPA 12), are available for use in total flooding (unmanned area) or local fire protection applications.

The cylinder shall be located in an environment protected from the weather and where the in a room temperature that does now exceed 54°C (130°F) nor fall below 0°C (32°F). The cylinders are tested to 250 bars and conform to ISO 9809, DOT-3AA, BS5045 PART 1 & NFPA 12.


Model: D-611

Water Capacity: 68L             

CO2 Gas Capacity: 45Kg

Test Pressure: 225 bar

Empty wight: 75Kg

Material: Mn Steel

Heigh:1500mm

Manufacture toBS EN ISO, 9809-1:2010, DOT-3AA

  
CYLINDER VALVE (MODEL D-617)

  • Eco-Friendly and Cost Effective
  • Protection Effective
  • Non-damaging to property
  • Automatic Actuation
  • Remote Manual Actuation
  • Direct Manual Release
ModelD-617
MaterialBrass
Working Pressure150 bar
Type
Manual/Pneumatic
 
PILOT CYLINDER (MODEL D-612)


  • Eco-Friendly and Cost Effective
  • Protection Effective
  • Non-damaging to property
  • Automatic Actuation
  • Remote Manual Actuation
  • Direct Manual Release
ModelD-612
ComponentPilot Cylinder
GasCO2
Voltage24VDC

HIGH HEAT TEMPERATURE DETECTOR (MODEL D-143)


The Demco Detector is a heat sensitive electrical switch. It is a fixed temperature device with a factory pre-set temperature 232°C.

The D-143 Detector comprises of normally open electrical contacts mounted within a stainless steel probe. A rise in temperature will cause the contacts to close at the set point temperature. With the drop in temperature the procedure reverses and the contacts re-open below set point temperature.

The detector body is a precision machine from AISI304 Stainless Steel with high corrosion resistance. The operation parts are factor calibrated and sealed against severe environmental condition, further adjustment or calibration is not required.


DISCHARGE NOZZLE (MODEL D-614)


Model: D-614

Material: Brass

Size: 15mm, 20mm, 25mm

Discharge Pattern: Uni-bilateral

Discharge: With orifice

Type: Pendent


MANUAL PULL BOX (MODEL D-619)


Model: D-619

Dimension: 104mm x 183mm x 75mm

Material: Steel metal box

Painting: Powder coated



TRIPPING DEVICE (MODEL D-615)

Model: D-609 & D-619

Material: High strength glass fiber

Power: 24 VDC

Ampere: 400mA

  • Eco-Friendly and Cost Effective
  • Protection Effective
  • Non-damaging to property
  • Automatic Actuation
  • Remote Manual Actuation
  • Direct Manual Release



EASIZON PANEL (MODEL D-020-EPC)

  • Available in two 4 zone models. The Easizon D-020 is expandable to 12 and 20 zones while the Easizon D-036 is expandable to 28 and 36 zones.
  • Being extremely compact and user-friendly, given their fast trouble-free installation and uncomplicated programming procedures, these control panels are ideal for all small and medium applications.
  • Packed with numerous functions like timers, equational logic, etc. as well as functions for extensive flexibility like automatic output balancing, multifunction inputs, customizable outputs, gas function integration, etc.
  • Innovative connectivity capabilities (RS485 BUS for power supply stations, Internet connection, etc.), provide the tranquillity of knowing for sure that this powerful tool is capable of satisfying every need of every type of installation.
ModelD-020-EPC
Main Power Supply230V AC, 50/60Hz
Internal Power Supply19VDC – 28.5VDC
Battery Requirement2 x 12V 7AH
Battery Housing2 x 12V 7AH
Switching Power Supply1.4A @ 27.6VDC
Cable TypePVC/ Screen / Firerated Cable
Maximum detectors per zone32
Number of sounder circuit1
Maximum bell output800mA
Weight3kg (without batteries)
Dimension325 x 325 x 80 mm
Event logYes and Downloadable
 

FIRE EXTINGUISHANT PANEL (MODEL EP-203)

Fully compliant with EN 12094 part 1 (the European standard for Fixed Firefighting Systems – Components for Gas Extinguishing Systems), the panel epitomises quality, durability and reliability and is ideal for use in any area housing expensive, dangerous or irreplaceable items of equipment.

Featuring an intuitive 128 x 64 pixel 2-colour graphic display that gives clear and concise feedback to the user, installer and commissioning engineer, the panel also includes six monitored inputs, a time stamped log, adjustable flood times and volt-free changeover relays for fire, local fire, 1st stage active, 2nd stage active, extractor fan and fault.

The panel is supplied in an elegantly styled, durable enclosure with all of its electronics – apart from its powerful 3A EN54-4 switch mode PSU – mounted on a detachable metal bridge plate for ease of installation.

Power Supply Specification
Mains supply voltage230Vac, 50/60Hz
Internal power supply24Vdc nominal
Max. output current3A@230Vac
Power rating (including charging)1.5A cont., 3A peak
Battery type
2 x 12Vdc, 7Ahr VRLA type, connected in series
Battery charge current0.7A
Earth fault monitoringYES
Mains supply/battery charger monitored for failureYES
Batteries monitored for disconnection and failureYES
Quiescent current drain on mains fail40mA approx.

 EVACUATE SIGN LAMP (MODEL D-110)

  • Durable – Tough industrial design contructed with mild steel’
  • Luminary: Ultra Bright LED
  • Easy visible access from side and rear
  • Buzzer available upon request
  • Optional: Different Range of Casing Colour
  • Specific languages available on facial layout upon request

 GAS DISCHARGE SIGN (MODEL D-100)

Dimensions LxHxDxD1(roof)
265 x110 x90 80 mm
Lens ColourRed
Casing ColourBlack
Lens MaterialPolycarbonate
Casing MaterialMild Steel
Operating Voltage24V DC
Operating Current30mA
Flashing Rate
140 Flash per minute @ 24V
Fixing Method
Direct fixing using screw
Cable Routing
Rear and side antry
Ultra Bright LED6 pcs
Sound Level62dB @ 1 meter
Gross Weight1.4 kgs

  • Durable – Tough industrial design contructed with mild steel’
  • Luminary: Ultra Bright LED
  • Easy visible access from side and rear
  • Buzzer available upon request
  • Optional: Different Range of Casing Colour
  • Specific languages available on facial layout upon request

MANUAL KEY SWITCH (MODEL D-101KS)

Model D-101KS

Casing Material : ABS Plastic
Net Weight: 175g

 MANUAL KEY SWITCH (MODEL D-105)

Model D-105

Casing Material: Mild Steel
Net Weight: 760g

BEACON / SOUNDER (MODEL D-115-154L)

  • Functional – inherent design offers wide operating voltage range
  • Efficiency – Low power consumption with high output
  • Accessible – Removable conduit plug offers easy conduit entries
  • Versatile – Suitable for surface or flush mounting
  • Practical Design – Provision of thread protection plugs protect brass inserts when conceal fixing is necessary
  • Compatible – Works perfectly well with most detection system
  • Operating Voltage: 24V DC
  • Operating Current: 70mA
  • Dimensions (L x W x H): 88 x 76 x 193 mm

Keterangan lebih lanjut Hubungi Marketing kami di :

021 54380292

021 54380293

e-mail : pemadam@antibara.com

            mery@antibara.com

Menunjukkan 0 unsur
Urutkan 
 
Menunjukkan 0 unsur
Ċ
Ismail Suparman,
11 Sep 2022, 20.25
Ċ
KeyBox.pdf
(150k)
Ismail Suparman,
11 Sep 2022, 21.23