HFC227ea SYSTEM

 
HFC 227ea CYLINDER
DEMCO’s HFC227ea (CF3CHFCF3 Heptafluoropropane) is a UL listed colourless, odourless, liquefied compressed gas. It suppresses fire primarily by physically cooling down the flame through lowering temperature to a point at which combustion reactions cannot be sustained.

As a waterless fire suppressant, it leaves no residue, water or corrosion. It has acceptable toxicity for use in occupied spaces at design concentration. It can be used on many types of fires. It is environmentally friendly. It has zero ozone-depleting potential, low global warning potential and short atmospheric lifetime.

  • Engineered and pre-engineered systems available
  • Effective and fast fire suppression against electrical fire
  • Widely applicable, from sensitive electrical equipment to industrial applications using flammable liquid
  • Electrically non – conductive
  • Acceptable toxicity for use in occupied and concentrated spaces
  • No residue to clean up after dis- charge and environmentally friendly
  • Whole systems UL listed
   
ELECTRONIC SELENOID (MODEL CP 50025-2 / CP 91225-2)

Our Electronic solenoid valve is a normally closed valve requiring electrical energy to open. It is used to vent the pressure from the top of the piston in the cylinder valve, allowing the piston to slide upward and commence cylinder discharge. The electric solenoid valves are available in 6, 12, 24V DC and 120V AC.

The source of the electrical energy must be supervised for a break in the wiring, a ground or a short circuit. The cylinder discharge valve equipped with a solenoid valve is actuated by the control panel for releasing devices and is compatible with Context Plus clean agent systems.


  • Available in 6, 12, 24V DC and 120V AC
  • Simple installation to the system
  • Modern Design
  • Long Lasting

FLEXIBLE HOSE
This flexible hose is used to connect the cylinders valve to discharge piping. The hose has a grooved fitting at the cylinder end and a male groove fitting to connect to the piping.

DEMCO’s hoses are made of high pressure hydraulic rubber in the 1’’ to 1-1/2’’ sizes and of stainless steel in the 2-1/2’’ and 4’’ sizes. The stainless steel flexible braided hose may be installed horizontally or with a 90 degree bend radius.

PART NUMBERSIZEAMATERIAL
CP 602551”18"Rubber
CP 602561-1/2"18"Rubber
CP 602572-1/2"18"Rubber
CP912304”30 -1/2"Stainless Steel Braided


PISTON ACTUATOR (MODEL CP 61041)

The Piston Actuator is used for multiple / manifold systems. it has a pneumatically driven piston that depresses a Schrader check valve, thereby venting the pressure from the top of the piston in the cylinder valve, allowing the piston to slide upward and commence cylinder discharge. The pneumatic pressure require to operate the piston actuator is obtained from the “M” port of the cylinder that is designed as “Master” cylinder and is either mechanically and/or electrically actuated. It is made of high quality Brass, and mounts directly on top of the cylinder valves.


  • High quality brass construction
  • Mounts directly on top of cylinder valves
  • Self-Venting

LOCAL MANUAL CONTROL HEAD (MODEL CP 61033)

The Local Manual Control Head features a local lever driven that depresses a Schrader check valve, thereby venting the pressure from the top of the piston in the cylinder valve. This allow the piston to slide upward and commence cylinder discharge.The Local Manual Control Head mounts directly to a top plug adapter, which is located at the top of the cylinder valve. It is used for manual actuation of cylinder, and made of solid Brass. It is self-venting with a safety pin to prevent accidental discharge. 

  • Used for manual actuation of cylinder
  • Equipped with safety pull-pin to prevent accidental manual discharge of Clean Agent
  • Self-venting
  • Stainless steel operation lock-pin
  • Solid brass construction

PRESSURE SUPERVISORY SWITCH (MODEL CP 50138-2 (NO) / CP 50138-1 (NC)

The Pressure Supervisory Switch is used to monitor the pressure within the Clean Agent cylinder. If a cylinder has leaking, and the pressure drops to below 291±10 psig, the switch contacts will be activated, providing a signal to the Release Control Panel to indicate lost of pressure and/or leakages. The pressure supervisory switch is wired into a supervised circuit to give a trouble signal upon activation. 

One version of the switch is normally closed (N.C.) (Part Number: CP 50138-1) and the other version is normally open (N.O.) (Part Number: CP 50138-2). The Pressure Supervisory Switch is referenced in the pressure condition. 



NOZZLES

It assists in a quick and effective distribution of clean agent. Available size: 1/2″, 3/4″, 1″, 1-1/4″, 1-1/2″, 2″
  • Available in 6 sizes – 1/2″ to 2″
  • Specially designed for HFC227ea Clean Agent System
  • Uniform distribution of agent

FIRE SUPPRESSION CONTROL PANEL MODEL EP-203
  • One of the most powerful extinguisher panels of its class on the market with easy to program capability.
  • Includes three conventional detector circuits & sounder circuits (2 x 1st stage and 1 x 2nd stage) which are all line monitored for open and short circuit faults.
  • Able to program any combination of activated detector zones to automatically activate the extinguishant release sequence, which can be set to operate with or without a delay.
  • Minimum six monitored inputs are provided, including Hold and Abort for suspending or cancelling the release sequence at anytime.
  • Adjustable flood times.
  • Alarm counter to record the number of occasions the panel has been in alarm.
  • Time-stamped log.
  • Support for an optional relay expansion board to provide reset, mode, discharged, hold and abort outputs.
  • Support for up to two Solenoids or multiple Metrons type actuators and volt-free changeover relay contacts for fire, local fire, 1st stage active, 2nd stage active, extract fan and fault.
  • System expansion for extra flexibility
  • Can be connected to the EP203 via a monitored RS485 bus to include up to eight flush or surface remote status units, each with their own displays, manual release mechanisms and mode switches.
  • Single gang economy status units without displays (8 per system).
  • A host of other ancillary devices including system line terminators and hold off/abort buttons.




FIRE SUPPRESSION CONTROL PANEL MODEL EASIZONE D-020

  • Available in two 4 zone models. The Easizon D-020 is expandable to 12 and 20 zones while the Easizon D-036 is expandable to 28 and 36 zones.
  • Being extremely compact and user-friendly, given their fast trouble-free installation and uncomplicated programming procedures, these control panels are ideal for all small and medium applications.
  • Packed with numerous functions like timers, equational logic, etc. as well as functions for extensive flexibility like automatic output balancing, multifunction inputs, customizable outputs, gas function integration, etc.
  • Innovative connectivity capabilities (RS485 BUS for power supply stations, Internet connection, etc.), provide the tranquillity of knowing for sure that this powerful tool is capable of satisfying every need of every type of installation.
  • Supervised outputs (one on the motherboard and one on each added expansion) for the activation of audio-visual signalling devices, a customizable relay output, fault signaling outputs and two 24V outputs (one constant and one interruptible by installer-defined conditions).
  • Customizable control interface is made possible via a terminal that comes with each detection zone. It can be configured as: open-collector output (activated by programmable conditions), supervised input, or Gas 4-20mA detector interface.
  • Easy-to-read system information is obtained through the graphic display and LEDs on the frontplate.
  • 4 remote repeater panels (EasiLetUSee/LCD-Lite) are supported by RS485 BUS. These repeater panels replicate all the fire alarm system data and allow users to access and control the system in accordance with their authorized access level. The BUS also supports two power-supply stations which can be connected to allow supervision of their functionality, and activation/deactivation of their output power during predefined conditions.
  • Straightforward and trouble-free system programming from the control panel is achieved via easy- to-follow instructions on the display.
  • Intuitive programming is made possible via SmartLeague, an optional software that greatly simplifies the programming procedure plus allowing more controls.
  • Remote access via the Internet is realized by SmartLAN/485 board which allows the control panel to be connected to an Ethernet network. Once the remote connection has been established, it is possible to modify the configuration parameters, upload/download programming data and/or manage the system by means of the supervisory software based on SmartLook graphic maps.

SOUNDE BEACON MODEL D-115-154 L

  • Operating Voltage: 24V DC
  • Operating Current: 70mA
  • Dimensions (L x W x H): 88 x 76 x 193 mm
  • Functional – inherent design offers wide operating voltage range
  • Efficiency – Low power consumption with high output
  • Accessible – Removable conduit plug offers easy conduit entries
  • Versatile – Suitable for surface or flush mounting
  • Practical Design – Provision of thread protection plugs protect brass inserts when conceal fixing is necessary
  • Compatible – Works perfectly well with most detection system


INDOOR EXTINGUSHANT SYSTEM ANCILLARIES

The shrouded push-button design on Extinguishant Abort Switch D-108-POS-EA and System Abort Switch D-508-EA helps prevent inadvertent operation during the cancelation of extinguishant release sequence. In addition, D-508-EA consists of corrosion-resistance stainless steel faceplate and a modular switch assembly designed to mount on a standard double gang electrical enclosure. Resettable Extinguishant Release Call Point D-108-POS-ER’s simple ‘RESET’ mechanism consist of ABS plastic operating element that simulates break glass activation which is instantly reusable with no glass elements to break, lose or incorrectly fit when installing.

D-108-POS-EHO Extinguishant Hold Off Switch’s raised push button design is good for quick positive operation or momentary actuation when delaying the immenent suppression agent’s release.

Designed with ease of installation in mind, Demco’s indoor system activation devices D-108-POS series are extremely suitable for open-circuit system


 EVACUATE SIGN 

DEMCO’s Evacuate Sign D-110 is a versatile, compact-bright that is designed ideally for fire, security and hazard warning. The solid-state LED Evacuate Sign offers high intensity of illumination at very low current consumption. The lens and base are designed using a high grade Polycarbonate engineering plastic that has excellent resistance to impact and heat. D-110 is designed to work effectively with most detection systems incorporation central control equipment. It is ideal for low current applications such as battery powered alarm panels where back up battery power is dramatically reduced.

Dimensions LxHxDxD1(roof)
265 x110 x90 80 mm
Lens ColourRed
Casing ColourBlack
Lens MaterialPolycarbonate
Casing MaterialMild Steel
Operating Voltage24V DC
Operating Current30mA
Flashing Rate
140 Flash per minute @ 24V
Fixing Method
Direct fixing using screw
Cable Routing
Rear and side antry
Ultra Bright LED6 pcs
Sound Level62dB @ 1 meter
Gross Weight1.4 kgs
 

GAS DISCHARGE SIGN

DEMCO’s Gas Discharge Sign D-110 is a versatile, compact-bright that is designed ideally for fire, security and hazard warning. The solid-state LED Evacuate Sign offers high intensity of illumination at very low current consumption. The lens and base are designed using a high grade Polycarbonate engineering plastic that has excellent resistance to impact and heat. D-110 is designed to work effectively with most detection systems incorporation central control equipment. It is ideal for low current applications such as battery powered alarm panels where back up battery power is dramatically reduced.

Dimensions LxHxDxD1(roof)
265 x110 x90 80 mm
Lens ColourRed
Casing ColourBlack
Lens MaterialPolycarbonate
Casing MaterialMild Steel
Operating Voltage24V DC
Operating Current30mA
Flashing Rate
140 Flash per minute @ 24V
Fixing Method
Direct fixing using screw
Cable Routing
Rear and side antry
Ultra Bright LED6 pcs
Sound Level62dB @ 1 meter
Gross Weight1.4 kgs


Keterangan lebih lanjut Hubungi Marketing kami di :

Telp.

021 54380292

021 54380293

e-mail : 

pemadam@antibara.com

mery@antibara.com

Ċ
Ismail Suparman,
5 Sep 2022, 19.19
Ċ
Ismail Suparman,
5 Sep 2022, 19.19
Ċ
Ismail Suparman,
5 Sep 2022, 19.20
Ċ
Ismail Suparman,
5 Sep 2022, 19.20
Ċ
Ismail Suparman,
5 Sep 2022, 19.20
Ċ
Ismail Suparman,
5 Sep 2022, 19.20
Ċ
Ismail Suparman,
5 Sep 2022, 19.20
Ċ
Ismail Suparman,
5 Sep 2022, 19.20
Ċ
Ismail Suparman,
5 Sep 2022, 19.21
Ċ
Ismail Suparman,
5 Sep 2022, 19.21
Ċ
Ismail Suparman,
5 Sep 2022, 19.21
Ċ
Ismail Suparman,
5 Sep 2022, 19.22
Ċ
Ismail Suparman,
5 Sep 2022, 19.22
Ċ
Ismail Suparman,
5 Sep 2022, 19.22
Comments